top of page

GEO5

bridge-abutment-design-software-1_edited.jpg

Abutment

To design bridge abutments including wing walls, It allows to check the abutment for overturning, translation, bearing capacity of foundation soil.

anti-slide-pile-slope-design_edited.jpg

Anti-Slide Pile

Design of pile walls stabilizing slope movement or increasing safety factor of the slope.

beams-design_edited.jpg

Beam

Analysis of foundation beams resting
on elastic foundation (subsoil).

cantilever-retaining-walls-design_edited.jpg

Cantilever Wall

verify cantilever retaining wall design.
It offers a number of wall shapes and analyzes reinforced concrete cross-sections.

Computes basic earth pressures (active pressure, passive pressure and pressure at rest) acting upon an arbitrary shaped structure.

earth-pressure-calculation_edited.jpg

Earth Pressures

finite-element-analysis-software_edited.jpg

FEM

Analyze a wide range of geotechnical problems, including terrain settlement, sheet pile/diaphragm walls, slope stability, excavation analysis.

FEM-consolidation-time-dependent-settlement-analysis_edited.jpg

FEM–Consolidation

To perform time dependent settlement analysis under foundations, embankments and surface loads (surcharges). 

fem-earthquake-eiqenvalue_edited.jpg

FEM – Earthquake

To perform dynamic analysis of geotechnical structures loaded by ground motion.The program outputs the evolution of displacements, stresses, internal forces and other mechanical quantities and summarizes their maximum values.

Branding

fem-tunnels_edited.jpg

FEM – Tunnel

I’m a paragraph. Double click me or click Edit Text, it's easy.

To design and analyze tunnels. It include a specialized tools for the definition of tunnel lining, system of anchors and rock bolts and grouting-strengthen regions.

Read More >
fem-water-seepage_edited.jpg

FEM – Water Flow

I’m a paragraph. Double click me or click Edit Text, it's easy.

gabion-walls-design_edited.jpg

Gabion

This program is used for gabion wall design. It allows analysis of any structure shapes including overhangs requiring anchoring.

gravity-retaining-walls_edited.jpg

Gravity Wall

This program is used for design of gravity retaining walls. It offers
a range of wall shapes and verifies mass concrete cross-sections.

Program computes the evolution and steady state of the pore pressure distribution, degree of saturation in the unsaturated zone, seepage velocities and inflow/outflow through the model.

ground loss-subsidence-above-excavations_edited.jpg

Ground Loss

Analysis and determination of the shape of subsidence trough above excavations and to evaluate the damage to buildings situated in the affected area.

I’m a paragraph. Double click me or click Edit Text, it's easy.

masonry-wall-design_edited_edited.jpg

Masonry Wall

This program is used for design and analysis of reinforced masonry block wall according to various standards.

micropile-design-1_edited.jpg

Micropile

This program is used for verification of steel tube micropiles. When calculating the micropile bearing capacity, the program verifies both the root and shaft.

mse-walls_edited.jpg

MSE Wall

This program is used for verification of mechanically stabilized earth walls and segmental retaining walls reinforced by geogrids (georeinforcements).

Branding

nailed slope-design_edited.jpg

Nailed Slope

This program is used to design soil nail walls and slopes of various shapes with shotcrete cover or steel mesh.

pile-design_edited.jpg

Pile

Analysis of vertical bearing capacity
of a single pile loaded both in tension or compression, pile settlement as well as horizontal bearing capacity of a single pile.

pile CPT-design-based-on-cpt_edited.jpg

Pile CPT

This program verifies the vertical bearing capacity and settlement of piles, based on the results provided by (static) cone penetration tests (CPT) and standard penetration tests (SPT)

pile-group-design_edited.jpg

Pile Group

Analyze a pile group (pile raft foundation with a rigid pile cap) using both spring method (FEM), or analytical solutions. Both floating piles and piles fixed into subsoil can be considered.

Prefab walls-design_edited.jpg

Prefab Wall

This program is used to verify retaining walls made of prefabricated blocks (retaining block walls).

redi-rock-wall_edited.jpg

Redi-Rock Wall

​It allows analysis of gravity walls with Redi-Rock blocks, as well as calculation of MSE walls with Redi-Rock Positive Connection (PC) blocks and Mirafi geogrids.

rock-stability-design_edited.jpg

Rock Stability

Analyze the stability of rock slopes and walls for a specified type of failure, including a planar or polygonal slip surface or rock wedge.

settlement_edited.jpg

Settlement

Determine vertical settlement and
time-dependent consolidation of soils under embankments, foundations, earth dams and surface loads (surcharges).

shaft-design-of-circular_edited.jpg

Shaft

This program is used to analyze spatial earth pressures on circular shaft and determination of internal forces on the structure.

Sheeting Check_edited.jpg

Sheeting Check

Design of embedded retaining walls using the method of elasto-plastic non-linear analysis and calculate the deformation and pressures acting upon the structure, to verify the internal anchor stability

sheet-pile-wall-design-software_edited.jpg

Sheeting Design

Quickly design non-anchored walls and to make a basic design of anchored retaining walls (Sheet pile, Soldier pile, Diaphragm and Pile walls).

Slab-design_edited.jpg

Slab

The program Slab is used for design of foundation mats and slabs of any shape on elastic subsoil, using the Finite Element Method.

slope-stability-water-flow-calculation-of-pore-pressures-1_edited.jpg

Slope Stability – Water Flow

Determination of the pore pressures in the slope by using the steady state or transient groundwater seepage analysis by the finite element method.

spread-footings_edited.jpg

Spread Footing

Design of spread footings (spread
or strip footing)  subject to general load.It computes vertical
and horizontal bearing capacity, settlement and rotation of a footing(Punching)

spread-footing-design-based-on-cone-penetration-test-dimensioning_edited.jpg

Spread Footing CPT

Design and verification of spread footing foundations based on data from field tests (CPT, SPT, PMT).

Branding

stratigraphy-geological-model-1_edited.jpg

Stratigraphy

Designed to process results from site investigation (boreholes, wells, CPTs, DPTs, SPTs, DMTs ...), generate 2D or 3D geological models

stratigraphy-section_edited.jpg

Stratigraphy – Cross Sections

Cross Sections module is designed for easy creation of geological cross-sections (including lenses, faults).

stratigraphy-earthwork-modelling-1_edited.jpg

Stratigraphy – Earthworks

Earthworks module is designed for modelling structures, such as foundation pits, roads, railways, quarries, slopes, and others. It also provides calculation of earthwork or terrain movement volumes.

stratigraphy-logs-output-report-preview_edited.jpg

Stratigraphy – Logs

Geological data reporting from site investigation (boreholes, wells, SPT, CPT, DMT and more). It provides a comprehensive database of pre-defined templates

bottom of page